檢測認證人脈交流通訊錄
CEDAR 扭力計 DI-9M-8/08 
Torque Meter DI-9M-8/08
DI-9 series is most suitable for checking and controlling the torque of
Electric Screwdriver and Torque Driver.(1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display.
(2) Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
(3) Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
(4) Calculation of Maximum, Minimum, and Average Became Intelligible.
(5) The call of the saved data became easy. The output of data also became intelligible.
(6) Fault charge protection. It is pilot-lamp lighting during charge.
(7) Data Output is USB Form (B Type).
(8) Memory Data are 800 Affairs
(9) Real-time Output is Every 1 / 180 Seconds.
The best for everyday check of an electric driver
Wide measurement range (0 - 8000digit),
it corresponds to various set torques
Can measure without inversion/
rolling-back work efficiently by OW joint (PAT.P).Specification DI-9M-8 DI-9M-08 Measuring range 0.020-8 N･m 2.0-800 mN･m 0.20-80 kgf・cm0.020-8 kgf・cm 0.20-70 lbf・in 0.020-7 lbf・in Accuracy ±0.5% (499 digit or less ±3digit) Display The 4 figures digital display of LCD The measurement direction CW-CCW (right and left) Zero return by one touch Return to zero by pressing clear button. Measurement Mode Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)High and low limits judging functionHigh and low value are measurement within the limits, and can be set up.Real-time Output Load torque value is outputted every about1/ 180 second.The Maximum, the minimum, and the average value display The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels.Data Output ASCII format (baud rate 19200) Auto power save 10 minutes no use, automatically switch off. Power supply Ni-Cd chargeable battery 1.2V × 5cells 700mAh Charging time About 3hours Continuous working time About 12hours clearance It is a display clearance in set-up time. (0.1 - 3.0 sec) Socket size 20mm/ 9.5mm Dimension / Weight W:160×D:125×H:55 / About 1kg Recommend buffer accessories Measuring joint
OW-20/OW-60Measuring joint
OW-025/OW-10Cube (with a 5th page screw hole) 20x20x20
(M2.6/M3/M4/M5/M6 Tap processing)AC/DC adaptor Exclusive receipt case An inspection report, a proofreading certificate, a traceability system figure ※Do not use for measurement of impact tool.Do not apply more than the specified torque.● MEASURING JOINT OW series 
Since our company developed the buffer
with little influence of fricative,
stable measurement could be performed
Moreover ,it does not need to reverse-rotate
at the time of measurement,
and work efficiency improved.Specification Type OW-025 OW-10 OW-20 OW-60 Measuring range N･m 0.25 1 2 6 Mechanical life （times） 10,000 8,000 5,000 5,000 Outer
diameter
size
（mm）Bit
engagement
part
(screw part)M2.6 cross
recess screwM3 cross
recess screwM4 cross
recess screwM6 cross
recess screwThe standard screw is cross recess screw
but they may be altered as necessaryOutside diameter φ28 φ32 φ32 φ38 Height 44 51 51 69 Ｉnstallation 20square ×4(t) CEDAR 扭力計 DI-9M-8/08 Torque Meter DI-9M-8/08
DI-9 series is most suitable for checking and controlling the torque of
Electric Screwdriver and Torque Driver.(1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display.
(2) Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
(3) Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
(4) Calculation of Maximum, Minimum, and Average Became Intelligible.
(5) The call of the saved data became easy. The output of data also became intelligible.
(6) Fault charge protection. It is pilot-lamp lighting during charge.
(7) Data Output is USB Form (B Type).
(8) Memory Data are 800 Affairs
(9) Real-time Output is Every 1 / 180 Seconds.The best for everyday check of an electric driver
Wide measurement range (0 - 8000digit),
it corresponds to various set torques
Can measure without inversion/
rolling-back work efficiently by OW joint (PAT.P).Specification DI-9M-8 DI-9M-08 Measuring range 0.020-8 N･m 2.0-800 mN･m 0.20-80 kgf・cm0.020-8 kgf・cm 0.20-70 lbf・in 0.020-7 lbf・in Accuracy ±0.5% (499 digit or less ±3digit) Display The 4 figures digital display of LCD The measurement direction CW-CCW (right and left) Zero return by one touch Return to zero by pressing clear button. Measurement Mode Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)High and low limits judging functionHigh and low value are measurement within the limits, and can be set up.Real-time Output Load torque value is outputted every about1/ 180 second.The Maximum, the minimum, and the average value display The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels.Data Output ASCII format (baud rate 19200) Auto power save 10 minutes no use, automatically switch off. Power supply Ni-Cd chargeable battery 1.2V × 5cells 700mAh Charging time About 3hours Continuous working time About 12hours clearance It is a display clearance in set-up time. (0.1 - 3.0 sec) Socket size 20mm/ 9.5mm Dimension / Weight W:160×D:125×H:55 / About 1kg Recommend buffer accessories Measuring joint
OW-20/OW-60Measuring joint
OW-025/OW-10Cube (with a 5th page screw hole) 20x20x20
(M2.6/M3/M4/M5/M6 Tap processing)AC/DC adaptor Exclusive receipt case An inspection report, a proofreading certificate, a traceability system figure ※Do not use for measurement of impact tool.Do not apply more than the specified torque.● MEASURING JOINT OW series Since our company developed the buffer
with little influence of fricative,
stable measurement could be performed
Moreover ,it does not need to reverse-rotate
at the time of measurement,
and work efficiency improved.Specification Type OW-025 OW-10 OW-20 OW-60 Measuring range N･m 0.25 1 2 6 Mechanical life （times） 10,000 8,000 5,000 5,000 Outer
diameter
size
（mm）Bit
engagement
part
(screw part)M2.6 cross
recess screwM3 cross
recess screwM4 cross
recess screwM6 cross
recess screwThe standard screw is cross recess screw
but they may be altered as necessaryOutside diameter φ28 φ32 φ32 φ38 Height 44 51 51 69 Ｉnstallation 20square ×4(t) CEDAR 扭力計 DI-9M-8/08 Torque Meter DI-9M-8/08
DI-9 series is most suitable for checking and controlling the torque of
Electric Screwdriver and Torque Driver.(1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display.
(2) Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
(3) Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
(4) Calculation of Maximum, Minimum, and Average Became Intelligible.
(5) The call of the saved data became easy. The output of data also became intelligible.
(6) Fault charge protection. It is pilot-lamp lighting during charge.
(7) Data Output is USB Form (B Type).
(8) Memory Data are 800 Affairs
(9) Real-time Output is Every 1 / 180 Seconds.The best for everyday check of an electric driver
Wide measurement range (0 - 8000digit),
it corresponds to various set torques
Can measure without inversion/
rolling-back work efficiently by OW joint (PAT.P).Specification DI-9M-8 DI-9M-08 Measuring range 0.020-8 N･m 2.0-800 mN･m 0.20-80 kgf・cm0.020-8 kgf・cm 0.20-70 lbf・in 0.020-7 lbf・in Accuracy ±0.5% (499 digit or less ±3digit) Display The 4 figures digital display of LCD The measurement direction CW-CCW (right and left) Zero return by one touch Return to zero by pressing clear button. Measurement Mode Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)High and low limits judging functionHigh and low value are measurement within the limits, and can be set up.Real-time Output Load torque value is outputted every about1/ 180 second.The Maximum, the minimum, and the average value display The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels.Data Output ASCII format (baud rate 19200) Auto power save 10 minutes no use, automatically switch off. Power supply Ni-Cd chargeable battery 1.2V × 5cells 700mAh Charging time About 3hours Continuous working time About 12hours clearance It is a display clearance in set-up time. (0.1 - 3.0 sec) Socket size 20mm/ 9.5mm Dimension / Weight W:160×D:125×H:55 / About 1kg Recommend buffer accessories Measuring joint
OW-20/OW-60Measuring joint
OW-025/OW-10Cube (with a 5th page screw hole) 20x20x20
(M2.6/M3/M4/M5/M6 Tap processing)AC/DC adaptor Exclusive receipt case An inspection report, a proofreading certificate, a traceability system figure ※Do not use for measurement of impact tool.Do not apply more than the specified torque.● MEASURING JOINT OW series Since our company developed the buffer
with little influence of fricative,
stable measurement could be performed
Moreover ,it does not need to reverse-rotate
at the time of measurement,
and work efficiency improved.Specification Type OW-025 OW-10 OW-20 OW-60 Measuring range N･m 0.25 1 2 6 Mechanical life （times） 10,000 8,000 5,000 5,000 Outer
diameter
size
（mm）Bit
engagement
part
(screw part)M2.6 cross
recess screwM3 cross
recess screwM4 cross
recess screwM6 cross
recess screwThe standard screw is cross recess screw
but they may be altered as necessaryOutside diameter φ28 φ32 φ32 φ38 Height 44 51 51 69 Ｉnstallation 20square ×4(t) CEDAR 扭力計 DI-9M-8/08 Torque Meter DI-9M-8/08
DI-9 series is most suitable for checking and controlling the torque of
Electric Screwdriver and Torque Driver.(1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display.
(2) Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
(3) Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
(4) Calculation of Maximum, Minimum, and Average Became Intelligible.
(5) The call of the saved data became easy. The output of data also became intelligible.
(6) Fault charge protection. It is pilot-lamp lighting during charge.
(7) Data Output is USB Form (B Type).
(8) Memory Data are 800 Affairs
(9) Real-time Output is Every 1 / 180 Seconds.The best for everyday check of an electric driver
Wide measurement range (0 - 8000digit),
it corresponds to various set torques
Can measure without inversion/
rolling-back work efficiently by OW joint (PAT.P).Specification DI-9M-8 DI-9M-08 Measuring range 0.020-8 N･m 2.0-800 mN･m 0.20-80 kgf・cm0.020-8 kgf・cm 0.20-70 lbf・in 0.020-7 lbf・in Accuracy ±0.5% (499 digit or less ±3digit) Display The 4 figures digital display of LCD The measurement direction CW-CCW (right and left) Zero return by one touch Return to zero by pressing clear button. Measurement Mode Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)High and low limits judging functionHigh and low value are measurement within the limits, and can be set up.Real-time Output Load torque value is outputted every about1/ 180 second.The Maximum, the minimum, and the average value display The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels.Data Output ASCII format (baud rate 19200) Auto power save 10 minutes no use, automatically switch off. Power supply Ni-Cd chargeable battery 1.2V × 5cells 700mAh Charging time About 3hours Continuous working time About 12hours clearance It is a display clearance in set-up time. (0.1 - 3.0 sec) Socket size 20mm/ 9.5mm Dimension / Weight W:160×D:125×H:55 / About 1kg Recommend buffer accessories Measuring joint
OW-20/OW-60Measuring joint
OW-025/OW-10Cube (with a 5th page screw hole) 20x20x20
(M2.6/M3/M4/M5/M6 Tap processing)AC/DC adaptor Exclusive receipt case An inspection report, a proofreading certificate, a traceability system figure ※Do not use for measurement of impact tool.Do not apply more than the specified torque.● MEASURING JOINT OW series Since our company developed the buffer
with little influence of fricative,
stable measurement could be performed
Moreover ,it does not need to reverse-rotate
at the time of measurement,
and work efficiency improved.Specification Type OW-025 OW-10 OW-20 OW-60 Measuring range N･m 0.25 1 2 6 Mechanical life （times） 10,000 8,000 5,000 5,000 Outer
diameter
size
（mm）Bit
engagement
part
(screw part)M2.6 cross
recess screwM3 cross
recess screwM4 cross
recess screwM6 cross
recess screwThe standard screw is cross recess screw
but they may be altered as necessaryOutside diameter φ28 φ32 φ32 φ38 Height 44 51 51 69 Ｉnstallation 20square ×4(t)
推薦產品
- 日本制:"CEDAR"電批扭力測試儀
- 日本制:"SATO"自記式溫濕度記
- 日本制:"SIMCO"FMX-003靜電測
- 日本制:"TECLOCK"拉力計
- 日本制:"TECLOCK"橫向張力計
- 日本制:"TOHNICHI" TM系列指針
- 日本制:"TOHNICHI"CL型可換頭
- 日本制:"TOHNICHI"FTD系列度盤
- 日本制:"TOHNICHI"PQL系列扭力
- 日本制:"TOHNICHI"QL-MH系列扭
- 日本制:"TOHNICHI"QLLS系列扭
- 日本制:"TOHNICHI"QL型可調式
- 日本制:"TOHNICHI"TME系列數顯
- 日本制:"UNITTA"音波式皮帶張
- 日本制:"YOKOGAWA"指針式線才
